Zaczynają się padające ST31000524AS :|

Wymieniać go z jednym błędem, bo szczerze mówiąc chyba się tym razem wstrzymam. Wole mieć 1 błąd niż 12 godzin przerwy, bo znów ktoś wyrwie kabel od dysku obok.

Jakie wsadzają teraz dyski 1 TB ?

http://en.wikipedia.org/wiki/S.M.A.R.T. – parametr nie jest oznaczony na czerwono

187 0xBB Reported Uncorrectable Errors
Lower
The count of errors that could not be recovered using hardware ECC (see attribute 195).

Kod:

smartctl 5.41 2011-06-09 r3365 [x86_64-linux-2.6.38.2-xxxx-std-ipv6-64] (local build)
Copyright (C) 2002-11 by Bruce Allen, http://smartmontools.sourceforge.net

=== START OF INFORMATION SECTION ===
Device Model:    ST31000524AS
Serial Number:    9VPC7EXN
LU WWN Device Id: 5 000c50 02e6ce7f7
Firmware Version: JC45
User Capacity:    1,000,204,886,016 bytes [1,00 TB]
Sector Size:      512 bytes logical/physical
Device is:        Not in smartctl database [for details use: -P showall]
ATA Version is:  8
ATA Standard is:  ATA-8-ACS revision 4
Local Time is:    Tue Aug 23 12:20:41 2011 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
See vendor-specific Attribute list for marginal Attributes.

General SMART Values:
Offline data collection status:  (0x82) Offline data collection activity
                                        was completed without error.
                                        Auto Offline Data Collection: Enabled.
Self-test execution status:      (  0) The previous self-test routine completed
                                        without error or no self-test has ever
                                        been run.
Total time to complete Offline
data collection:                (  600) seconds.
Offline data collection
capabilities:                    (0x7b) SMART execute Offline immediate.
                                        Auto Offline data collection on/off support.
                                        Suspend Offline collection upon new
                                        command.
                                        Offline surface scan supported.
                                        Self-test supported.
                                        Conveyance Self-test supported.
                                        Selective Self-test supported.
SMART capabilities:            (0x0003) Saves SMART data before entering
                                        power-saving mode.
                                        Supports SMART auto save timer.
Error logging capability:        (0x01) Error logging supported.
                                        General Purpose Logging supported.
Short self-test routine
recommended polling time:        (  1) minutes.
Extended self-test routine
recommended polling time:        ( 173) minutes.
Conveyance self-test routine
recommended polling time:        (  2) minutes.
SCT capabilities:              (0x103f) SCT Status supported.
                                        SCT Error Recovery Control supported.
                                        SCT Feature Control supported.
                                        SCT Data Table supported.

SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG    VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate    0x000f  119  099  006    Pre-fail  Always      -      227432171
  3 Spin_Up_Time            0x0003  100  100  000    Pre-fail  Always      -      0
  4 Start_Stop_Count        0x0032  100  100  020    Old_age  Always      -      18
  5 Reallocated_Sector_Ct  0x0033  100  100  036    Pre-fail  Always      -      0
  7 Seek_Error_Rate        0x000f  087  060  030    Pre-fail  Always      -      471415321
  9 Power_On_Hours          0x0032  098  098  000    Old_age  Always      -      2422
 10 Spin_Retry_Count        0x0013  100  100  097    Pre-fail  Always      -      0
 12 Power_Cycle_Count      0x0032  100  100  020    Old_age  Always      -      18
183 Runtime_Bad_Block      0x0032  100  100  000    Old_age  Always      -      0
184 End-to-End_Error        0x0032  100  100  099    Old_age  Always      -      0
187 Reported_Uncorrect      0x0032  099  099  000    Old_age  Always      -      1
188 Command_Timeout        0x0032  100  099  000    Old_age  Always      -      65537
189 High_Fly_Writes        0x003a  100  100  000    Old_age  Always      -      0
190 Airflow_Temperature_Cel 0x0022  057  044  045    Old_age  Always  In_the_past 43 (0 40 52 38)
194 Temperature_Celsius    0x0022  043  056  000    Old_age  Always      -      43 (0 24 0 0)
195 Hardware_ECC_Recovered  0x001a  044  027  000    Old_age  Always      -      227432171
197 Current_Pending_Sector  0x0012  100  100  000    Old_age  Always      -      0
198 Offline_Uncorrectable  0x0010  100  100  000    Old_age  Offline      -      0
199 UDMA_CRC_Error_Count    0x003e  200  200  000    Old_age  Always      -      0
240 Head_Flying_Hours      0x0000  100  253  000    Old_age  Offline      -      95520072665508
241 Total_LBAs_Written      0x0000  100  253  000    Old_age  Offline      -      2869975268
242 Total_LBAs_Read        0x0000  100  253  000    Old_age  Offline      -      3171808865

SMART Error Log Version: 1
ATA Error Count: 1
        CR = Command Register [HEX]
        FR = Features Register [HEX]
        SC = Sector Count Register [HEX]
        SN = Sector Number Register [HEX]
        CL = Cylinder Low Register [HEX]
        CH = Cylinder High Register [HEX]
        DH = Device/Head Register [HEX]
        DC = Device Command Register [HEX]
        ER = Error register [HEX]
        ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 1 occurred at disk power-on lifetime: 2414 hours (100 days + 14 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 00 ff ff ff 0f  Error: UNC at LBA = 0x0fffffff = 268435455

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC  Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  25 00 80 ff ff ff ef 00  2d+17:07:19.336  READ DMA EXT
  ca 00 30 51 ec a4 e7 00  2d+17:07:19.335  WRITE DMA
  ca 00 d8 79 eb a4 e7 00  2d+17:07:19.312  WRITE DMA
  ca 00 78 01 eb a4 e7 00  2d+17:07:19.312  WRITE DMA
  c8 00 08 79 eb a4 e7 00  2d+17:07:19.312  READ DMA

SMART Self-test log structure revision number 1
No self-tests have been logged.  [To run self-tests, use: smartctl -t]

SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.


Cytat:

ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
ata1.00: irq_stat 0x40000001
ata1.00: failed command: READ DMA EXT
ata1.00: cmd 25/00:80:81:d8:83/00:00:52:00:00/e0 tag 0 dma 65536 in
res 51/40:00:e8:d8:83/00:00:52:00:00/00 Emask 0x9 (media error)
ata1.00: status: { DRDY ERR }
ata1.00: error: { UNC }
ata1.00: configured for UDMA/133
ata1: EH complete